How to Square A Board with a Table Saw? Step-by-Step Guide

For a skilled carpenter, squaring a board is a simple task. However, if you have to find this article, chances are you are an amateur. Do not worry, through this step by step guide you will get the best results. Let’s find out how to square a board with a table saw.

Basic steps for squaring a board with a table saw

Square a board with a table saw is not complicated. You just need to follow some basic steps below:

  • Step 1: Create sketch lines on the broad surface
  • Step 2: Use a fence to get the desired length 
  • Step 3: Use the right saw blade, do not forget to adjust it
  • Step 4: Use personal protective equipment
  • Step 6: Run the board through the table saw

Let’s take a deep look at those steps!

Step 1: Create sketch lines on the broad surface

Whatever shape you need to cut the board in, you should start with marking the board with a ruler and pencil. 

In addition, you can also use any tool that can mark on the board. As a result, you can see your results in advance on the surface of the board.

How to Square A Board with a Table Saw

Sketching on the surface of the board will greatly determine the size and shape of your product. That means this drawing has a very important role.

You may also need to use a square plate. They will be useful in drawing straight lines on the board surface. They are also especially useful when you need to draw two lines that are perpendicular to each other.

Step 2: Use a fence to get the desired length 

After completing the sketch on the board, you can run it through the table saw right away. 

If you are a skilled carpenter, you will not need any extra tools for this. However, this is a step by step guide for beginners, so we would recommend a little extra preparation.

Specifically, you should prepare a fence. It allows you to cut exactly the length you need. All you need to do is place the fence according to your sketch and fix it.

Then your board is ready to run through the table saw.

Step 3: Use the right saw blade, do not forget to adjust it

Once your board is ready, you need to focus on choosing the right saw blade.

In general, the standard table saw blade is not a bad choice. You can get a good job done with it. However, we recommend a serrated saw blade. This type of saw blade is very effective in cutting thick boards accurately.

You should use a serrated saw blade

Once you have your saw blade, you should adjust it a bit. 

The important thing is that you have to place the saw blade perpendicular to the table. This is to make sure it can cut exactly what you want. 

Based on the thickness of your board, you will decide the height of the saw. In fact, the saw blade height should be slightly higher than the board thickness.

Step 4: Use personal protective equipment

Before officially starting, you should protect yourself!

The use of saw blades may pose some risk to you. While this does not happen often, you should still take precautions. It is wise to have all the safety equipment in place before you start using the table saw. 

Specifically, you should use goggles (safety glasses) to protect your eyes. Do not forget to use earplugs to protect your ears. You should also wear gloves to avoid scratching.

You should use goggles to protect your eyes

Step 5: Run the board through the table saw

After completing the above steps, it Is time to do the cutting. Turn on the saw and slowly push the board towards the saw. Note that the hand cannot be too close to the saw blade to avoid a serious accident.

You should do it slowly

Pro Tips

  • You should lengthen your saw’s table

This is especially necessary when you need to cut large sheets. You can do this by pairing another table with the saw’s table. However, you need to make sure they are the same height.

  • Using  a set of push sticks

Thanks to using this tool, you can run the board through the table saw without using your hands. Therefore, touching the saw blade is impossible. 

  • Do it slowly

A skilled carpenter can perform this task quickly. However, as a beginner, you should not rush. Rushing can lead you to make mistakes!

Let’s start very slowly. Over time, your technique will get better.

Related Articles:

 Frequently Asked Questions

1. What alternatives are there to a fence?

A fence is the best option. However, you can use a clamped strip or a guide as perfect alternatives.

2. What do I need to create sketch lines on the broad surface?

It is best to use a pencil and a ruler. In addition, you can also use a framing square as an alternative to the ruler.

3. Why should I wear safety glasses (goggles)?

When you run the board through the saw, it can create wood chips. These wood chips can get in your eyes. We all don’t want that to happen, do we?

4.  What alternatives are there to a table saw?

With a table saw, you can easily square a board. However, that is not the only option. In fact, you can also accomplish that with a planner or even a jointer. The most important thing is that you do it right.

Conclusion

Hopefully, you have a clear understanding of the methods to square a board with a table saw. It is not as complicated as you think, is it? Just follow the basic directions above, you will get the best results.

Reference Source: How to square any piece of wood using only a table saw and a straight board

Leave a Comment