How to install quarter round without a nail gun? 

The quarter ring is an important part to bridge the gap between the floor and the wall. It makes your home look more beautiful and complete. The workers will use a nail gun to install the ring. 

However, what if you are a normal person without a nail gun? In this article we will show you how to install quarter round without a nail gun.

How to install quarter round without a nail gun with a hammer?

  • Step 1: Cut the mold
  • Step 2: Place the mold against the wall and flat with the floor
  • Step 3: Drive the nail into the wall
  • Step 4: Drive the rest of the nails with a set of nails
  • Step 5: Fill the gaps with glue
  • Step 6: Cover nail heads

Installing a quarter round between the baseboard and the floor helps to cover the holes. It increases the elegance of the house and is more durable for the floor. 

If you don’t have a nail gun, you can completely install a quarter round with a nail hammer. You need to prepare a hack saw, hammer, finishing nails, nail set and latex sealant/caulk. 

Step 1: Cut the mold

Cutting a quartet mold will be very easy with a hacksaw. A hack saw will make manual adjustment more convenient. But you can also use another type of saw that you are most comfortable with.

Cut the quarter round to fit the length of the floor and wall

Step 2: Place the mold against the wall and flat with the floor

When placing the mold against the wall and flat with the floor, you may notice small gaps appear. This is understandable since it is difficult to achieve perfect precision when cutting a quadri. 

You just need to pay attention to the correct mounting of the mold. Those holes can be filled with glue.

Step 3: Drive the nail into the wall

Many people make the mistake of driving nails into the floor. You have to nail the wall to get the technique right. Hold the nail tilted and use a hammer to drive it instead of driving horizontally. 

You have to perform the closing slowly to ensure certainty. If you close too hard and continuously, you can easily chip the baseboard. This hammer nailing is also easy to drive your finger. Drive until about 1/8 inch of nail is still sticking out of the wall.

Step 4: Drive the rest of the nails with a set of nails

First, you need to align the nail set in the direction of the nail. Choose a set of nails with a tip that is smaller than the nail you drove. Then use the hammer to drive the set of nails in its direction.

This step requires very high precision. You can practice first on another board. Note that you must place the posts about two feet apart along the length of the baseboard.

Step 5: Fill the gaps with glue

Now it’s time for you to remove the small gaps between the quartet mold and the wall. Use special glue to do this. Then use your fingers to smooth the glue.

There will be parts of glue sticking out of those gaps. Please wipe clean with a paper towel. Blaming that glue to dry will ruin the quarter round.

You can use special glue to remove the small gaps between the quartet mold and the wall

Step 6: Cover nail heads

After nailing, the tip of the nail will make tiny dots appear on the quarter round. Remove them with a special coat of paint. 

This will be easier if the baseboard is white with white glue. If they’re not the same color, you’ll have to blur them a little harder.

How to install quarter round without a nail gun with special glue?

  • Step 1: Measure and cut the mold
  • Step 2: Prepare quarter round
  • Step 3: Apply glue
  • Step 4: Attach the quarter round to the wall
  • Step 5: Clean the excess glue

You don’t have a nail gun for a quarter round. But you don’t want to use a hammer either. 

There’s an easier method for you that doesn’t involve both nails and a nail gun or hammer. You can absolutely use special glue to install the quarter round. Here are detailed instructions for you:

Step 1: Measure and cut the mold

The measurement and cutting need to be accurate and meticulous to avoid creating too big a gap between the wall and the floor. It also helps to create the necessary corner joints.

Step 2: Prepare quarter round

You need to determine which side of the quarter round sticks to the wall. Then, use sandpaper to sand the surface to create roughness. This helps to increase the bond between the wall and the quarter round.

Step 3: Apply glue

Apply glue to the surface you have sanded. Be careful not to apply too much. If you apply too much glue, it will make the adhesive layer messy and even spill out.

Step 4: Attach the quarter round to the wall

Stick the quarter round to the wall according to the surface you have applied scissors on. You have to hold it firmly for a few minutes for the glue to dry and stick together.

You have to hold quarter round  firmly for a few minutes for the glue to dry and stick together

Step 5: Clean the excess glue

Wipe away the sticky layers of scissors around the area with a sponge. Especially the seam between the quarter round and the base of the wall.

It is easier and safer to install a quarter round with special glue than with a hammer or nail gun. You won’t have to worry about hurting your fingers. 

But with this way, the adhesion will not be as good as with nails. The layers of glue will bond messy and unsightly if you apply too much. When you want to improve the quarter round, it will be very difficult to remove them.

A few tips on installing quarter round without a nail gun

  • Carefully check the dimensions of the mold

You must measure everything as carefully and accurately as possible. Avoid cutting the molding too short, making the quarter round shorter than the floor and wall lengths.

  • Don’t forget to blur the nail tips

After installing the quarter, many people often forget about this step. If you don’t fade the tips of the nails with a specialized paint, they will ruin your quarter round aesthetic.

  • Wipe off any remaining glue layers

It is much easier to clean the glue layers when they are not yet dry. If you let the layers dry, it will stick to the walls and floor. It will take you a long time to clean them.

Final Thoughts

Here’s how to instal a quarter round without a nail gun. We hope that it will help you in renovating your home.

Reference Source: How To Install Baseboard Without a Nail Gun or Fasteners!

 

Leave a Comment