How To Clean Bandsaw Tires: The Best Ways For You

Excessive accumulation of sawdust and pitch on your bandsaw tires will happen once. It’s an easy task to clean your bandsaw tires. As long as you keep these things in mind. And remember to take the appropriate precautions.

In this article, we’ll prepare you the methods to clean bandsaw tires. Stay tuned and find out.

How to clean bandsaw tires?

To clean bandsaw tires, there are two popular and easy ways:

  • Clean with soap or cleaner
  • Clean without soap or cleaner

 

How To Clean Bandsaw Tires: The Best Ways For You

Clean with soap or cleanser

Some hardwoods don’t leave any residue. But pine and green wood will make your saw dirty quickly.

If the bandsaw is very stubborn. You may need a cleaner or a soapy detergent to clean it.

Make sure whatever you use is safe for rubber application.

Collect the following objects before you start cleaning:

  • 120-grit of sandpaper
  • An old sturdy toothbrush
  • A piece of cotton towel
  • 2050 blade cleanser or any other appropriate water-based cleaning

After you got all the ingredients, following these instructions carefully:

  • Step 1: Remove the bandsaw: Safety is your first priority. Before conducting any normal maintenance, always start disconnecting your bandsaw.
  • Step 2: Take the saw blade off: The next step is to remove the saw blade. You have to do this to ensure it’s safe to work on screws. And incline the table to better reach the tires.
  • Step 3: Start cleansing the bandsaw tire: The bottom bandsaw tire usually has more pollution accumulated. There initially, you may clean it with care.
  • Step 4: Apply the cleaner on the wheel: Using an old toothbrush to apply cleaner. Then leave it there for 15 minutes. The cleaner may loosen the sawdust and dirt.
  • Step 5: Scrape the tire with a toothbrush: Remove the resin and other waste from the tire with a toothbrush. Be mild to avoid scratching or damaging the rubber.
  • Step 6: Dry the tire before using: Once it’s clean, properly dry with a cotton cloth. Or let it dry in the sunlight. Making sure the tire is dry will prevent slipping or rusting.

Apply wax to maintain your bandsaw

Clean without soap or cleanser

You do not need to use soap or cleaner every time. If you have chopped resinous wood such as pine. You should not require cleansers or soap.

With this method, you will need the same ingredients as the method above.

In the same way, execute steps 1 to 3 of the previous procedure first. And proceed with the following steps.

  • Step 4: Screw the wheel of the bandsaw

After cleansing, you can start scraping the wheel of the bandsaw. Using some thin sandpaper (120-grit one that you had prepared before).

Most of the obstinate sawdust will be removed while using this. Keep rubbing the tire lightly throughout.

Then rub the wheel until all visible waste is removed with an old toothbrush.

  • Step 5: Use a cotton towel or cloth to wipe the tire

The last step is to use a cotton towel and wipe your tire. Wipe it carefully to remove any remaining dust or obstinate.

Use sandpaper to rub bandsaw tire

How often should you clean bandsaw tires?

The frequency of cleaning your tires depends on how much it is used and how regularly.

If you cut green or sawn wood, wait for the bandsaw to be cleaned more often. To maintain the saw in optimal working conditions. You may think of it as routine maintenance.

Whenever you use your bandsaw on board, small particles. Bits of sawdust build on the tube of the device. In particular, on the bottom of the tires.

If you are a light user. And the device works well. You may only need to clear your scout periodically.

On the other hand, if you often cut resinous wood which leaves residues of pitching. Or there are pine tar and sawdust on your tires. You may need to clean it more frequently and carefully.

Use a bandsaw brush to clean the tire

Mistakes should avoid, Tips to follow

There are some mistakes and tips we would like to show you in this section:

  • Do not use any cleaner or liquids for the purification of rubber. Do not use them on urethane tire pipes either. It can cause caustics or be hazardous.
  • Avoid using oven cleaners, alcohol-containing solutions. Or anything can produce oily residues on the tires.
  • You should dry the bandsaw overnight before trying to clean the tires.
  • Dry scraping and accumulation are much easier to remove.
  • We recommend using a scraper for the gunk cleanup.
  • Keep the rubber from damaging the gunk by not using abrasive sandpaper, iron wool, or other things.

 

Related Articles:

Frequently Asked Questions

1. Do you need to oil your bandsaw?

A saw blade from the device is a piece of equipment. You must lubricate both sides. In both situations, we know for a fact that lubricating the band’s body enhances the device’s lifetime.

It can increase to more than 30%.

When used judiciously, you may cut grade timber without discoloration.

2. How do you protect your bandsaw from rust?

If you have to use soapy water. Make sure to fully dry your blade with a towel before applying a lubricant to prevent corrosion.

After using your bandsaw, clean the area. Next, add a bandsaw-approved liquid or solid-form wax lubrication to the blade. Other metal surfaces need to have the same routine.

3. How do you maintain your bandsaw?

To maintain your device’s performance, you need to do these things: clear debris. Remove dust, dirt, or carbon dust. You also have to apply wax and remove the blade off. Finally, remember to clean your saw regularly.

Conclusion

Now you don’t have to worry about “how to clean bandsaw tires”. We provided the best methods for you. Choose your cleaning method carefully based on your device’s situation.

Reference source: How to Clean Bandsaw Tires | Tricks of the Trade

Leave a Comment